注册 登录  
 加关注
   显示下一条  |  关闭
温馨提示!由于新浪微博认证机制调整,您的新浪微博帐号绑定已过期,请重新绑定!立即重新绑定新浪微博》  |  关闭

史提芬邹的博客

锐臣专业工具旗舰店

 
 
 

日志

 
 

史提芬邹电动工具缺陷分类  

2009-10-26 19:24:31|  分类: 史提芬邹电动工具 |  标签: |举报 |字号 订阅

  下载LOFTER 我的照片书  |

classification/缺陷分类

Critical Defect ( A )/极严重缺陷

       
  ? A defect which experience and judgment indicates is likely to result in a hazardous and/or injurious situation.
   to the user, or makes the product subject to governmental seizure.
Major Defect ( B )/主要缺陷        
  ? Any unit having a defect other than critical is likely to result in failure, or to reduce materially the usability of
  the unit for its intended purpose. Any unit having a aesthetics defect or construction problem which is deviated
  from the standard. At a result, which can cause a customer return.
Minor Defect ( C )/次要缺陷        
  ? Any unit having a defect that is not likely to reduce the usability of the unit for its intended purpose, or is
   departure from established standards having little bearing on the effective use of the products.
1.Safety /安全        
Item 故障描述 Failed Description Defect Classification 
1 高压失效 Hi-Pot  test  failed A    
2 短路 Short circuit A    
3 接地线路不良 Earth continuity check failed A    
4 错相 Wrong polarity A    
5 电源线不过开关直接接到马达 Power cower connected to motor directive A    
6 电源线被损坏 ( 露銅 ) Damaged power cord/internal wire(cupper wire can be seen) A    
7 电源线拉力测试不通过 Strain relief check failed(power cord pull test failed) A    
8 用错电源线/内部导线 Wrong power cord/wire used A    
9 端子可以用小于2.5 公斤力拉出 Terminal can be separate with less than 5 Lbs.  A B  
10 电子零件(switch/power cord/capacitor /L/..etc)供应商不是证书上所要求 Electric parts are not from the appoint supplier as certified required. A    
11 下护罩回弹不良和卡住 Lower guard can't retain /or blocked  A    
12 锯片切喉板 Blade cutting the thropple plate  A    
13 开关无关的功能 Switch lost off function A    
14 開關安全鎖鎖不住 Switch Lock off  function failed A    
15 開關安全鎖按下回彈失敗 Switch lock off knob can't spring back . A    
16 跌落測試失敗 Drop test failed  Hold the shipment
17 溫升超過標准 temperature rise exceed spec. A    
18 吊帶易脫 Lanyard can broken easily. A    
19 強度測度失敗 Failed Strength Test A    
20 加載後的永久性變形 Permanent deformation was found after a load was applied A    
21 尖邊 / 尖角 / 毛刺 / 飛邊 且易傷手. Sharp edge / point / burr / flash A    
22 砂輪開裂 Crack of sander disc A    
23 帶電零件易接觸到 Live part can be accessibility A    
24 內部電線及電線連接器 易觸及 Internal wire and wire connector were accessible  A    
25 過載保護囂沒功能  switch reset failure A    
26 主要部件更改未通過CCDR. changed main part has not pass CCDR. A    
27 开机后飞出不明物 Unknown parts blow out in operation A    
           
2.Function /功能        
Item 故障描述 Failed Description Defect Classification 
1 不能啟動 Unit doesn't turn on    B  
2 間歇開關 Intermittent switch (INT)   B  
3 LED 顯示面板功能失效;                          指示燈不亮 LED display panel didn't function;                                               the indicator lighting did not light   B  
4 殼離大(0.5) Big gap between housing   B  
5 夾頭跳動超差 Runout of chuck out of spec   B  
6 轉動方向錯誤 Wrong rotational direction   B  
7 機器無法關機 machine couldn't be turned off A B  
8 馬達死機 Motor can't run    B  
9 底座擺動 Wobbling at base    B  
10 底座不平 Uneven base    B  
11 振動 Vibration   B  
12 異常的噪音(異音) Abnormal noise   B  
13 超出正常的分貝標準 Exceeds indicated dB level   B  
14 零件錯誤 Incorrect components Hold the shipment
15 切割深度/角度超出標準 Cutting depth/cutting angle over spec.(Out of spec.)   B  
16 刀刃變形 Deformed edge    B  
17 火花大 Big spark from carbon brush   B  
18 電流大 Current out of spec   B  
19 轉速超額定值 Speed out of spec A B  
20 轉子劃傷定子 Rotor scratch stator   B  
21 電線切面積偏小 Power cord cupper wire cross area out of spec (less) A    
22 開關鎖定失敗 Switch Lock on  function failed   B  
23 螺絲未打緊 Screw loose    B  
24 後手柄轉彎不良 Rear handle rotary not smooth   B  
25 调速无功能 Variable speed adjustment failed   B  
26 高低调速旋鈕无功能 Hi-low speed knob with out function   B  
27 低压启动测试失败 Low voltage start up  failure Hold the shipment 
28 堵转测试失败 Failed in lock rotor test   B  
29 鋸片裝不上 Blade can't put in    B  
30 夾頭夾不到规程中尺寸 Drill bits can't be hold by chuck within capacity   B  
31 激光灯不亮,不对焦 Laser no function, laser lines not in center of X   B  
32 刻度不对 零 Scale not match the ''0''   B  
33 漏零件;漏加胶水  Missing parts/   glue  A B  
34 異味 abnormal smell Hold the shipment
3.Surface/外观         
Item 故障描述 Failed Description Defect Classification 
1 凹坑 Dents  ;  void   B C
2 劃傷 Scratches    B C
3 磨損 Scuffs  ;   Weared   B C
4 小孔 Punctures   B C
5 缺角 Chipped corner   B  
6 顏色不合要求 color don't match color chip   B  
7 銹跡 Rust mark   B C
8 油污 Oil stains   B C
9 塵垢 Dust stains   B C
10 表面毛刺 Burr on surface    B C
11 表面標簽損壞, 表面有針孔 Label was broken; pinhole on surface   B C
12 百格測試(附着力测试) 100 grids test failed Hold the shipment
14 油漆剝落 Paint peeled off
13 砂眼 / 砂孔 Sand spot, sand hole   B C
14 表面粗糙 Surface rough   B C
16 电镀不良 Poor plating   B C
17 缩水,发白 Shrink   B C
18 丝印不良 Poor silk-screening   B C
19 皱纹 Wrinkle   B C
20 变形 Deformation   B C
21 部件破裂/裂紋 part crack  A B  
22 縮水 sink     C
23 紋理 texture failure      C
24 表面发白 Whiten on surface    B C
25 電源線被損壞(未露銅) Damaged power cord/internal (cupper wire can't be seen)   B  
           
4.Missing/缺失        
Item 故障描述 Failed Description Defect Classification 
1 配件袋中缺少橡皮刷 Missing rubber washer in accessory bag   B  
2 袋裡缺少"索賠單" Missing warranty sheet from unit package   B  
3 缺少SKU#標貼 Missing a SKU# label   B  
4 缺少日期標貼 Missing date code label   B  
5 缺少 " UL & CE "標志 Missing " UL" or ' CE'  marking A    
6 缺少手冊 Missing manual A    
7 " UL " 標誌有細微地損壞 UL label was damaged slightly   B C
8 所用手冊安全項不正確 Ownering manual in safety items is incorrect . A    
9 所用手冊非安全項不正確 Ownering manual is incorrect not concern the safety item .   B C
10 警告標志不清楚 Warning marking was illegible A    
11 標貼有皺紋 Label was wrinkled   B  
12 標簽的印刷郊果太差 Poor printing of label   B  
13 裡面有氣泡 Air bubble inside   B  
14 死蟲/頭髮在機器或者包裝裡面 Dead insect /hair inside  unit or packing  A B  
15 濕氣 Moisture Hold the shipment
16 包裝袋內有水 Water inside of unit(packing)
17 螺絲缺少 Short screw    B  
18 標簽翹起 Label peel off   B  
19 缺少唛头 Missing shipmark   B  
20 缺少两年保修期标签 Missing guarantee label   B  
21 朔膠包装袋上未打孔.(口寬大過175mm) No air hole on polybag with open  larger than 7''. A    
22 包装袋上缺少三国语言 The bag missing three type of language Hold the shipment
23 短少附件 Missing accessory    B  

  评论这张
 
阅读(151)| 评论(0)
推荐 转载

历史上的今天

评论

<#--最新日志,群博日志--> <#--推荐日志--> <#--引用记录--> <#--博主推荐--> <#--随机阅读--> <#--首页推荐--> <#--历史上的今天--> <#--被推荐日志--> <#--上一篇,下一篇--> <#-- 热度 --> <#-- 网易新闻广告 --> <#--右边模块结构--> <#--评论模块结构--> <#--引用模块结构--> <#--博主发起的投票-->
 
 
 
 
 
 
 
 
 
 
 
 
 
 

页脚

网易公司版权所有 ©1997-2017